Can You Easy Out a Threaded Taper Pin

Joined
Jun 5, 2017
Messages
80
  • #1

Hello ;

I am trying to restore an Atlas 618 lathe that was given to me. I have it all apart to clean, replace parts that need replacing and then paint and put it back together again. However, I am stuck at trying to get the rack off the lathe bed. The screws came out easy enough, but there are two taper pins there to locate the rack and hold it in place. One of those pins seem to be accessible from the inside , but the other was installed where the bed is thick- right at one of the webs.There are threaded holes for the screws that hold the rack on, and those holes are bored and threaded all the way through that side of the bed, and also one hole where it seems I could try to punch out one of the taper pins from the inside of the bed, but no way to get at the other one from the inside.
These pins are in there TIGHT! I am afraid of trying to pry up the rack from the outside of the bed because I would probably screw something up in a really big way. I would really be interested in hearing from anyone with any suggestions on how to get this off without damaging the rack, the taper pins or the lathe bed. Thanks in advance for any help.

f350ca

Forum Guest

Register Today

  • #2

Could you drill the pin, thread it and then jack it out with a screw and suitable spacers?

Greg

4ssss

Registered

Registered

Joined
Apr 25, 2017
Messages
752
  • #3

Are you sure they are taper pins? Normally they won't use a taper pin in a blind hole.

RJSakowski

RJSakowski

H-M Supporter - Gold Member

H-M Supporter Gold Member

Joined
Feb 1, 2015
Messages
7,417
  • #4

My Atlas Craftsman 6 x 18 uses a 1/8" dowel pin. Is it possible that a previous owner replaced the OEM pins with tapered pins? In any event, I would remove the screws and gently pry the rack out with a thin blade. If you can drive one pin out you could rotate the rack slightly to loosen the second pin. With any outward movement, a tapered pin should free up.

Joined
Jun 5, 2017
Messages
80
  • #5

Could you drill the pin, thread it and then jack it out with a screw and suitable spacers?

Greg

Thanks for the idea, but these taper pins are very small in diameter. Drilling them would mean using an even smaller drill bit and a tap so small that it would probably be considered "micro" in size.

Joined
Jun 5, 2017
Messages
80
  • #6

My Atlas Craftsman 6 x 18 uses a 1/8" dowel pin. Is it possible that a previous owner replaced the OEM pins with tapered pins? In any event, I would remove the screws and gently pry the rack out with a thin blade. If you can drive one pin out you could rotate the rack slightly to loosen the second pin. With any outward movement, a tapered pin should free up.

That's verty interesting; I called it a taper pin because that is what the machine manufacturers usually use to "locate" items like this precisely. It might not even be a taper pin for all I know, since I haven't managed to get them out yet. But I am probably going to try your suggestion, and thanks for letting me know that yours has dowel pins in it. More than likely mine does too but I just didn't know it!

4GSR

Forum Guest

Register Today

  • #7

Many racks I have removed from lathe beds were held in with either roll or spring pins, and straight dowel pins. Haven't run across anywhere where tapered pins were used.

Silverbullet

Joined
May 4, 2015
Messages
3,583
  • #8

Taper pins , usually are used to hold handles or gears or two piece shafts . I'd soak the area around the pins , I'd also use a propane torch and play it around the pin areas. The heat will open the holes and spaces slightly , tap the area with a soft hammer to set up vibrations which believe me works. You don't have to get the area red hot just a few hundred degrees. Sometimes two or three times over a 24 hrs period . Usually a couple taps with brass hammer will make it come apart. Try a clamp or vise grip to pull on the rack gently .

Joined
Jun 5, 2017
Messages
80
  • #9

Many racks I have removed from lathe beds were held in with either roll or spring pins, and straight dowel pins. Haven't run across anywhere where tapered pins were used.

Well I have received comments from others on this forum that state that a rack is not hard to bend in the process of removal. Because of that, I have changed my mind about removing these pins and will leave it in place, tape it up and clean and paint around it. But thanks for your input!

T Bredehoft

Joined
Dec 27, 2014
Messages
3,865
  • #10

Probably the best you can do. just verify that the bed for the rack is totally clean when you put it all beck together. no dust under it.

garrettcapperes.blogspot.com

Source: https://www.hobby-machinist.com/threads/how-to-safely-remove-taper-pins.60292/

0 Response to "Can You Easy Out a Threaded Taper Pin"

Post a Comment

Iklan Atas Artikel

Iklan Tengah Artikel 1

Iklan Tengah Artikel 2

Iklan Bawah Artikel